Cleaning and Maintenance:
Before cleaning or maintaining the device, the supply cable must be disconnected.
Under no circumstances should the product be cleaned by running water on its outer surfaces or by placing it in a container filled with water.
Never clean using abrasive hard materials or Chemicals.
These materials can damage your device.
Surfaces should not be wiped with cleaning wire, sandpaper or similar abrasive materials.
Cleaning should not be done with sharp or piercing tools.
If icing is present, it should never be attempted to dislodge it with sharp or penetrating materials.
In this case, warm water should be run over the ice.
After emptying the water inside the device, you should wipe it with a dry and clean cloth.

Melting Process:
Depending on the setting value of the cooler, frost may form on the side walls.
If the temperature of the cooler is above 0C, these frosts will melt automatically at the end of each operation.
However, if the set value is below 0 C, they will turn into icing over time.
There is a decrease in the productivity of the product. Therefore, it should be melted at regular intervals.

Follow The Steps Below For Melting:
Remove the contents of the device. If possible, put it in another refrigerator.
So that it does not overheat. Stop the operation of the device at the on/off switch.
Turn the cover fully open. If there is excessive frosting, run warm water on the frosted surfaces.
Wait for the ice to thaw. Empty the melted ice water from the appliance and pour it out.
Never use melted ice water as drinking water.
Do not use these ices to cool drinks.
After emptying the water inside the device, you should wipe it with a dry and clean cloth.

Operation With Solar Panel
First of all, you should run the car refrigerator over a battery. You must connect the (+) Plus end (Red Cable) of the solar panel to the Plus terminal, and the (-) Negative end (Black Cable) to the Battery. You should connect the solar panel to the ends of the battery in the same way. In order to keep the current value low, it is useful to choose a 24V DC Solar panel as much as possible. You should definitely install a 15A fuse between the car refrigerator and the battery. This is essential for general safety. In case of any short circuit, the circuit must be protected by a fuse. According to the models of the products we produce and the operating temperature range (according to whether they are operated as a Cooler or Freezer), the power of solar panel and battery you should use is given in the table below. It is useful to choose 24V DC solar panels.

What should be considered in order for the Car Refrigerator to consume less electricity? Place your device in a well ventilated place protected from direct sunlight. Sunlight can heat your device. This may cause it to remain active for a longer period of time. After waiting for freshly cooked or heated hot food to cool, place it in the appliance. Do not open and close the appliance door unnecessarily. Do not keep the appliance door open for an unnecessarily long time. When a layer of ice forms on the surface of the device, melt the ice and turn the device on again after cleaning it. If possible, put the food you take out of it in another cooler during this process and prevent it from getting hot. Do not set your device to extremely cold values unnecessarily. Reaching excessively cold values will cause unnecessary Energy consumption of the product.

Solar Panel & Battery Selection Chart

Cable Cross Section and Length Selection Chart
Since your device works with Direct Current, resistance losses on the line are very important. For this reason, you should run your connecting cable at the shortest possible distance. There should not be any additional additional connections on the line. As far as possible, the device connection should never be disassembled or reassembled. Cable cross-sections according to the distance to be used are given below.

Car Refrigerator Energy Saving Suggestions
Place your device in a well-ventilated and shaded area protected from direct sunlight. Sunlight can heat your device. This may cause it to remain active for a longer period of time. After waiting for freshly cooked or heated hot food to cool, place it in the appliance. Do not open and close the appliance door unnecessarily. Do not keep the appliance door open for an unnecessarily long time. If a layer of ice forms on the surface of the device, melt the ice and turn the device on again after cleaning it. If possible, put the food you take out of it in another cooler during this process and prevent it from getting hot. Do not set your device to extremely cold values unnecessarily. Reaching excessively cold values will cause unnecessary Energy consumption of the product.